View PC901V0NSZX_1188813.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PC901V0NSZX
PC901V0NSZX
s Features
1. Normal ON operation, open collector output 2. TTL and LSTTL compatible output 3. Operating supply voltage (VCC:3 to 15V) 4. Isolation voltage (Viso (rms):5kV) 5. High sensitivity (IFLH:MAX. 2.0mA at Ta=25C) 6. Under preparation for UL standard 7. 6-pin DIP package
Digital Output Type OPIC Photocoupler
s Outline Dimensions
PC901VoNSZX
6 5 4
(Unit : mm)
Internal connection diagram Voltage regulator
6 4 5
6.50.3
Anode mark
PC901V
Amp
1 2 3
1
2
3
0.60.2 1.20.3
s Applications
1. Programmable controllers 2. PC peripherals 3. Electronic musical instruments
7.120.3
7.620.3
3.250.5 3.50.5
2.90.5
0.5
TYP.
s Absolute Maximum Ratings
0.260.1 =0 to 13
(Ta=25C) Unit mA A V mW V V mA mW mW kV C C C
0.5
0.1
Parameter Symbol Rating 50 Forward current IF *1 Peak forward current IFM 1 Input Reverse voltage VR 6 Power dissipation P 70 VCC 16 Supply voltage High level output voltage VOH 16 Output Low level output current IOL 50 Power dissipation PO 150 Total power dissipation Ptot 170 *2 Isolation voltage Viso (rms) 5 Operating temperature -25 to +85 Topr -40 to +125 Tstg Storage temperature *3 Soldering temperature Tsol 260
*1 Pulse width100s, Duty ratio=0.001 *2 40 to 60%RH, AC for 1 min *3 For 10 s
2.540.25
1 2 3
Anode Cathode NC
4 5 6
Vo GND VCC
"OPIC"(Optical IC) is a trademark of the SHARP Corporation. An OPIC consists of a light-detecting element and signalprocessing circuit integrated onto a single chip.
Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device. Internet Internet address for Electronic Components Group http://www.sharp.co.jp/ecg/
PC901V0NSZX s Electro-optical Characteristics
Parameter Forward voltage Input Reverse current Terminal capacitance Operating supply voltage Low level output voltage High level output current Low level supply current High level supply current
*4
Symbol VF IR Ct VCC VOL IOH ICCL ICCH IFLH
Output
"LowHigh" threshold input current
"HighLow" threshold IFHL input current *6 Hysteresis IFHL/IFLH Isolation resistance RISO "LowHigh" propagation delay time tPLH "HighLow" propagation delay time tPHL Rise time tr Transfer Fall time tf charac- *8 Instantaneous common teristics mode rejection voltage CMH "Output : High level" Response time
*7 *8
*5
(Ta=0 to +70C unless otherwise spesified) Unit MIN. TYP. MAX. - 1.1 1.4 V 1.0 - 0.7 A - 10 - - 250 pF 30 3 - 15 V - 0.2 0.4 V IOL=16mA, VCC=5V, IF=4mA - - 100 A VO=VCC=15V, IF=0 - 5.0 mA 2.5 VCC=5V, IF=0 VCC=5V, IF=4mA - 5.5 mA 2.7 Ta=25C, VCC=5V, RL=280 - 1.1 2.0 mA 4.0 - - VCC=5V, RL=280 0.4 0.8 - Ta=25C, VCC=5V, RL=280 mA VCC=5V, RL=280 0.3 - - - VCC=5V, RL=280 0.9 0.5 0.7 - Ta=25C, DC=500V, 40 to 60%RH 5x1010 1011 - 1 3 Ta=25C - 2 6 VCC=5V, IF=4mA s 0.5 - 0.1 RL=280 0.5 - 0.05 Conditions IF=4mA IF=0.3mA Ta=25C, VR=4V Ta=25C, V=0, f=1kHz VCM=600V(peak), VO(MIN.)=2V IF=4mA, RL=280, Ta=25C VCM=600V(peak), VO(MAX.)=0.8V IF=0, RL=280, Ta=25C - - -2 000 - - V/s
Instantaneous common mode rejection voltage "Output : Low level"
CML
2 000
V/s
*4 IFLH represents forward current when output goes from low to high. *5 IFHL represents forward current when output goes from high to low. *6 Hysteresis stands for IFHL/IFLH. *7 Test circuit for response time is shown below. *8 Test circuit for CMH, CML shown below.
Fig.1 Test Circuit for Response Time
Voltage regulator VIN tPHL tPLH 50%
5V tr=tf=0.01s ZO=50 VIN 47 Amp 0.1F 280 VO
VO tf
VOH 90% 1.5V 10% VOL tr
PC901V0NSZX Fig.2 Test Circuit for CMH and CML
Switch for Infrared LED IF
Voltage regulator 600V 5V 280 VCM Switch for Infrared LED at A (IF=0) VO(MAX.)=0.8V Switch for Infrared LED at B (IF=4mA) VO(MIN.)=2V VCM GND VOL GND
B
A Amp. + -
VO 0.1F
Fig.3 Forward Current vs. Ambient Temperature
60
Fig.4 Power Dissipation vs. Ambient Temperature
200 170 Power dissipation PO, Ptot (mW) 150 Ptot PO
50
Forward current IF (mA)
40
30
100
20
50
10 0 -25
0
25
50
75 85
100
0 -25
0
25
50
75 85
100
Ambient temperature Ta (C)
Ambient temperature Ta (C)
Fig.5 Forward Current vs. Forward Voltage
500 200 Forward current IF (mA) 100 50 20 10 5 2 1 0 0.5 1 1.5 2 2.5 3 Forward voltage VF (V) Ta=75C 50C
Fig.6 Relative Threshold Input Current vs. Supply Voltage
1.4
Ta=25C IFLH=1 at VCC=5V IFLH
25C 0C -25C
Relative threshold input current
1.2
1
IFHL
0.8
0.6
0.4 0.2
0
5
10
15
20
Supply voltage VCC (V)
PC901V0NSZX Fig.7 Relative Threshold Input Current vs. Ambient Temperature
1.6
Fig.8 Low Level Output Voltage vs. Low Level Output Current
1 VCC=5V IF=0 Ta=25C
VCC=5V
1.4
Relative threshold input current
1.2 1 0.8
IFLH
Low level output voltage VOL (V) 50 75 100
0.5
0.2 0.1
IFHL
0.6 0.4 0.2 0 -25
0.05 0.02 0.01 1 2 5 10 20 50 100 Low level output current IOL (mA)
IFLH=1 at Ta=25C 0 25
Ambient temperature Ta (C)
Fig.9 Low Level Output Current vs. Ambient Temperature
0.5 VCC=5V Low level output voltage VOL(V) 0.4 IOL=30mA
Fig.10 High Level Output Current vs. Forward Current
10 VCC=5V High level output current IOH(A) 5 Ta=25C
0.3 16mA 0.2
2 1
0.5
0.1
5mA
0.2 0 -25 0.1 0 25 50 75 100 0 10 20 30 40 50 60 Ambient temperature Ta(C) Forward current IF(mA)
Fig.11 High Level Output Current vs. Ambient Temperature
2 High level output current IOH(A) 1 0.5 VCC=VO=15V IF=4mA
Fig.12 Supply Current vs. Supply Voltage
9 8 7 Supply current ICC(mA) 6 5 4 3 Ta= 2 -25C{ 25C{ 1 85C{ 0 0 2 4 6 8 ICCH ICCL ICCH ICCL ICCH ICCL
0.2 0.1 0.05 -25 0 25 50 75 100
10
12
14
16
18
Ambient temperature Ta(C)
Supply voltage VCC(V)
PC901V0NSZX Fig.13 Propagation Delay Time vs. Forward Current
6 Propagation delay time tPHL, tPLH (s) VCC=5V RL=280 Ta=25C tPHL 0.5 Rise time, fall time tr, tf(s)
Fig.14 Rise Time, Fall Time vs. Load Resistance
0.6 VCC=5V IF=4mA Ta=25C
5
4
0.4
3
0.3
2
0.2
tr
1 tPLH 0 0 10 20 30 40 50 60 Forward current IF(mA)
0.1 tf 0 0.2 0.5 1 2 5 10 20
Load resistance RL(k)
s Precautions for Use
1. It is recommended that a by-pass capacitor of more than 0.01F is added between VCC and GND near the device in order to stabilize power supply line. 2. Handle this product the same as with other integrated circuits against static electricity. 3. As for other general cautions, please refer to the chapter "Precautions for Use".
Application Circuits
NOTICE
qThe circuit application examples in this publication are provided to explain representative applications of SHARP devices and are not intended to guarantee any circuit design or license any intellectual property rights. SHARP takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of SHARP's devices. qContact SHARP in order to obtain the latest device specification sheets before using any SHARP device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. Manufacturing locations are also subject to change without notice. qObserve the following points when using any devices in this publication. SHARP takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) The devices in this publication are designed for use in general electronic equipment designs such as: --- Personal computers --- Office automation equipment --- Telecommunication equipment [terminal] --- Test and measurement equipment --- Industrial control --- Audio visual equipment --- Consumer electronics (ii)Measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when SHARP devices are used for or in connection with equipment that requires higher reliability such as: --- Transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- Traffic signals --- Gas leakage sensor breakers --- Alarm equipment --- Various safety devices, etc. (iii)SHARP devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- Space applications --- Telecommunication equipment [trunk lines] --- Nuclear power control equipment --- Medical and other life support equipment (e.g., scuba). qContact a SHARP representative in advance when intending to use SHARP devices for any "specific" applications other than those recommended by SHARP or when it is unclear which category mentioned above controls the intended use. qIf the SHARP devices listed in this publication fall within the scope of strategic products described in the Foreign Exchange and Foreign Trade Control Law of Japan, it is necessary to obtain approval to export such SHARP devices. qThis publication is the proprietary product of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. qContact and consult with a SHARP representative if there are any questions about the contents of this publication.
115

▲Up To Search▲

Price & Availability of PC901V0NSZX

	To Download PC901V0NSZX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .